Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Advice on attaching the secondary mirror?
( viewtopic.php?f=4&t=12693 )
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- NGC 1365
- Articles: 0
- Posts: 368
- Joined: Mon Dec 02, 2019 8:30 am
- 4
- Location: NSW Australia
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Close. The offset in not really a problem, but the direction is. It's so easily that I could make the major axes of the holder and the mirror point some degrees in different direction.
I was thinking of printing a sablon - something like yours.
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- NGC 1365
- Articles: 0
- Posts: 368
- Joined: Mon Dec 02, 2019 8:30 am
- 4
- Location: NSW Australia
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
My tube is shown in my signature: 300mm / 1200 mm
I was thinking of a "guide" like this for making marks on the side of the secondary and the holder.
(Or maybe I'll make another one for the holder.)
The black lines are the lines of minor and major axes, and the red one is the "optical minor axis" that is offset by 4.7 mm from the "geometrical minor axis". The separation of the black and red lines should be 6.6 mm.
The ends of the red line are drawn in 45° so that they fold nicely upwards (along the holder).
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- NGC 1365
- Articles: 0
- Posts: 368
- Joined: Mon Dec 02, 2019 8:30 am
- 4
- Location: NSW Australia
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
I'm not going to mark the secondary center. I think I'll just add the alignment lines on the sides of the secondary.
My spider vanes don't have enough play to make the offset by adjustment. There are 4 vanes and the front vanes make a 45 degree angle with the focuser. So the adjustment needs to be 6.6 mm, and the vanes are a bit too short.
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
(I don't know why the drawing is shown so small.)
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- NGC 1365
- Articles: 0
- Posts: 368
- Joined: Mon Dec 02, 2019 8:30 am
- 4
- Location: NSW Australia
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Like I said, there is no vane directly towards focuser, but two vanes at + and - 45°. To get the holder to move 4.7 mm, the vanes in 45° needs to go back 6.6 mm. (6.6 mm x cos 45° = 4,667 mm, quite good enough, although the angle changes slightly as the vanes get longer)
Actually, I even tried, but the "front vanes" were so "at the edge" that I didn't have the nerve to leave it that way (less than 2mm thread inside the plastic adjustment nut).
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- NGC 1365
- Articles: 0
- Posts: 368
- Joined: Mon Dec 02, 2019 8:30 am
- 4
- Location: NSW Australia
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
You can notice that the mirror surface is slightly skewed (rotated clockwise) compared to the back side. There is a noticeable angle between the major axis of the mirror surface and the major axis of the back side. Also the left side is perpendicular to the surface, but the right side is obviously not. The mirror surface itself seems to be ellipse with 75 mm minor axis and 106 mm major axis.
That's why some mask/shablon/template is needed.
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
That much skew - see the angle between the bolt and the major axis drawn on the template.
Just try collimating the secondary mirror...
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
The same needs to be to the secondary holder too, after the secondary is removed from the holder.
And yes, now the bolt points to the geometrical center of the mirror - there is no offset.
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
This is the picture from the back side with the markers. You can see the reflective coating through the glass - except in the upper part where there is that 45° slope outwards, and the reflective surface continues under it.
You can see the asymmetry of the glass - and the back side.
The red vertical line is the major axle of the reflecting face brought to the back side. The horizontal line is the offset-line = line parallel to minor axis but moved downwards by the amount of the offset. The upper short horizontal lines are markers for 4.5 mm thick nail (spacer). The other spacer is 2.5 mm thick nail at the edge of the lower end of the holder. That should fix the 43.5° holder angle (instead of the 45°).
The arcs of ellipse are the shape of the holder. Since the holder is hollow, I need to check that the silicon goes in places where there is holder.
The mirror is upside down in more ways than one: back-side up, and "vane side" down.
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
- turboscrew
- Articles: 0
- Posts: 3233
- Joined: Sat Jun 20, 2020 9:22 am
- 3
- Location: Nokia, Finland
- Status:
Offline
-
TSS Awards Badges
Re: Advice on attaching the secondary mirror?
Senior Embedded SW Designer
Telescope: OrionOptics XV12, Mount: CEM120, Tri-pier 360 and alternative dobson mount.
Grab 'n go: Omegon AC 102/660 on AZ-3 mount
Eyepieces: 26 mm Omegon SWAN 70°, 15 mm TV Plössl, 12.5 mm Baader Morpheus, 10 mm TV Delos, 6 mm Baader Classic Ortho, 5 mm TV DeLite, 4 mm and 3 mm TV Radians
Cameras: ZWO ASI 294MM Pro, Omegon veLOX 178C
OAG: TS-Optics TSOAG09, ZWO EFW 7 x 36 mm, ZWO filter sets: LRGB and Ha/OIII/SII
Explore Scientific HR 2" coma corrector, Meade x3 1.25" Barlow, TV PowerMate 4x 2"
Some filters (#80A, ND-96, ND-09, Astronomik UHC)
Laptop: Acer Enduro Urban N3 semi-rugged, Windows 11
LAT 61° 28' 10.9" N, Bortle 5
I don't suffer from insanity. I'm enjoying every minute of it.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute