https://www.thingiverse.com/thing:3957102
diy spherometer
-
yobbo89
- Moderator
- Articles: 0
- Posts: 2597
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Online
-
TSS Photo of the Day
diy spherometer
printed this simple spherometer, didn't have ball end grub screws but it does have 3 printed contact points that some what work until i get some adjustment screws , i purchased joe's old mirror he had in storage from an old project he started years ago, i gave it a little test run, it read f5.47 @ 1380mm fl , the mirror is very close to where i want it to be. atm i'm also working on a 3d printed bath interferometer
https://www.thingiverse.com/thing:3957102
https://www.thingiverse.com/thing:3957102
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
-
yobbo89
- Moderator
- Articles: 0
- Posts: 2597
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Online
-
TSS Photo of the Day
Re: diy spherometer
And here's part of the bath interferometer, need to order some prisms and a laser
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
-
OzEclipse
- Moderator
- Articles: 2
- Posts: 2391
- Joined: Sat May 11, 2019 8:11 am
- 4
- Location: Young, NSW, Australia, 34S, 148E
- Status:
Online
-
TSS Awards Badges
TSS Photo of the Day
Re: diy spherometer
Nice stuff Rob. I couldn't quite remember the final f ratio but I think I said I thought it was somewhere around f5.6, not bad memory after 40 years!
If you can manage with the current f5.5, you can go straight to polishing. This will save you a lot of time, having to glue glass facets to the tool then grind them in to match the surface then remove the facets afterwards prior to polishing.
How important is that extra 1/2 stop?
Will be following this project with interest.
Good luck
Joe
If you can manage with the current f5.5, you can go straight to polishing. This will save you a lot of time, having to glue glass facets to the tool then grind them in to match the surface then remove the facets afterwards prior to polishing.
How important is that extra 1/2 stop?
Will be following this project with interest.
Good luck
Joe
Amateur astronomer since 1978...................Web site : http://joe-cali.com/
Scopes: ATM 18" Dob, Vixen VC200L, ATM 6"f7, Stellarvue 102ED, Saxon ED80, WO M70 ED, Orion 102 Maksutov, ST80.
Mounts: Takahashi EM-200, iOptron iEQ45, Push dobsonian with Nexus DSC, three homemade EQ's.
Eyepieces: TV Naglers 31, 17, 12, 7; Denkmeier D21 & D14; Pentax XW10, XW5, Unitron 40mm Kellner, Meade Or 25,12
Cameras : Pentax K1, K5, K01, K10D / VIDEO CAMS : TacosBD, Lihmsec.
Cam/guider/controllers: Lacerta MGEN 3, SW Synguider, Simulation Curriculum SkyFi 3+Sky safari
Memberships Astronomical Association of Queensland; RASNZ Occultations Section; Single Exposure Milky Way Facebook Group (Moderator) (12k members), The Sky Searchers (moderator)
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute