new mount ,using sitech, horizon limit and star alighnment
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
new mount ,using sitech, horizon limit and star alighnment
I have my new mount, mesu 200v2 setup and connected to the pc and is sending commands, but i'm getting a error with below horizon limit , my settings are so far correct with my lat long, i think my scope is facing the wrong direction or something, i guess only very few here use sitech, sky view blinks rapidly and the crossair of where the mount is nowhere to be seen, but i can slew it and after awhile it will show and i set it to park position ie south and do a star alignment at the park position but it still gives me below horizon limit..
any ideas ?
any ideas ?
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- UlteriorModem
- Local Group Ambassador
- Articles: 0
- Posts: 2112
- Joined: Sat May 11, 2019 1:32 am
- 4
- Location: Florida
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
Don't know this mount but first thing I would check is the slew limits set in the hand controller.
Also check the date and time and double check the location.
Also check the date and time and double check the location.
Tom
Current Equipment:
Mount: Celestron CGX-L
Scope: 130mm f7 APO
Cam: ASI071mc-pro
Current Equipment:
Mount: Celestron CGX-L
Scope: 130mm f7 APO
Cam: ASI071mc-pro
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
I will check the date and time, the hc is very basic, all of the controll data is done via pc rs232 serial com, I know how to map the horizon slew limits but it still shows the error
.
.
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- SkyHiker
- Local Group Ambassador
- Articles: 0
- Posts: 2293
- Joined: Sat May 11, 2019 8:40 pm
- 4
- Location: Santa Barbara, CA
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: new mount ,using sitech, horizon limit and star alighnment
Did you use the servoConfig instructions? http://siderealtechnology.com/ServoConfig.pdf
It has instructions on how to configure the directions in which the motors move.
I was just browsing the SiTech site, not claiming any expertise here and I presume you did this already.
It has instructions on how to configure the directions in which the motors move.
I was just browsing the SiTech site, not claiming any expertise here and I presume you did this already.
... Henk. Telescopes: GSO 12" Astrograph, "Comet Hunter" MN152, ES ED127CF, ES ED80, WO Redcat51, Z12, AT6RC, Celestron Skymaster 20x80, Mounts and tripod: Losmandy G11S with OnStep, AVX, Tiltall, Cameras: ASI2600MC, ASI2600MM, ASI120 mini, Fuji X-a1, Canon XSi, T6, ELPH 100HS, DIY: OnStep controller, Pi4b/power rig, Afocal adapter, Foldable Dob base, Az/Alt Dob setting circles, Accessories: ZWO 36 mm filter wheel, TV Paracorr 2, Baader MPCC Mk III, ES FF, SSAG, QHY OAG-M, EAF electronic focuser, Plossls, Barlows, Telrad, Laser collimators (Seben LK1, Z12, Howie Glatter), Cheshire, 2 Orion RACIs 8x50, Software: KStars-Ekos, DSS, PHD2, Nebulosity, Photo Gallery, Gimp, CHDK, Computers:Pi4b, 2x running KStars/Ekos, Toshiba Satellite 17", Website:Henk's astro images
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
Thanks for the link, I'll have a read, I emailed lucas and he sent me his sitech CONFIG file, i just have to put in my lat and long.
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
ok i've fixed this , lucas gave me his profile and i've got it working with the newest sitech version, i was using an older one, park and unpark work and save, and moving around on the sky map works as well.
I guess this is a feature to have the scope start upside down, i think you can pick east looking west, vice versa for nonemeridian flips.
now i have to try and get stellarium to work andsgp .
I guess this is a feature to have the scope start upside down, i think you can pick east looking west, vice versa for none
now i have to try and get stellarium to work and
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- UlteriorModem
- Local Group Ambassador
- Articles: 0
- Posts: 2112
- Joined: Sat May 11, 2019 1:32 am
- 4
- Location: Florida
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
Well if noting else it makes it easier to get to the mounted equipment
Tom
Current Equipment:
Mount: Celestron CGX-L
Scope: 130mm f7 APO
Cam: ASI071mc-pro
Current Equipment:
Mount: Celestron CGX-L
Scope: 130mm f7 APO
Cam: ASI071mc-pro
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
I guess I can attach a dslr or small refractor on the cw end
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- SkyHiker
- Local Group Ambassador
- Articles: 0
- Posts: 2293
- Joined: Sat May 11, 2019 8:40 pm
- 4
- Location: Santa Barbara, CA
- Status:
Offline
-
TSS Photo of the Day
TSS Awards Badges
Re: new mount ,using sitech, horizon limit and star alighnment
It will hit the legs sooner with the scope upside down. Isn't there a better configuration? This is weird.
I just wonder, since this looks like a small one person shop in the Northern hemisphere, if a mistake was made in the configuration. I'm looking at the servoConfig manual, it says:
4. Motor Directions
a. Azimuth should go clockwise when pressing the right button on the handpad (birds eye view).
b. R/A should go clockwise when viewed from Polaris
c. Altitude should move up when the up button is pressed
d. Declination should move toward the pole when the telescope is looking on the West side of theMeridian .
5. Telescope Encoder Directions: The telescope encoder numbers should change in the same direction as the motors encoder numbers, ie increase while the motor is increasing.
In the Southern hemisphere, I think (b) should be "R/A should go counterclockwise when viewed from theSCP ". About (a) I'm not so sure - for reasons of symmetry I think Az should move in the opposite direction in response to commands to the Northern hemisphere, while it does make sense to have Az go clockwise when you push the right button. How this jives with the telescope and motor encoders, I have no idea.
It's altogether confusing because for the drive, Alt=DEC and Az=RA . I would consult with SiTech because they must have customers in the Southern hemisphere.
I just wonder, since this looks like a small one person shop in the Northern hemisphere, if a mistake was made in the configuration. I'm looking at the servoConfig manual, it says:
4. Motor Directions
a. Azimuth should go clockwise when pressing the right button on the handpad (birds eye view).
b. R/A should go clockwise when viewed from Polaris
c. Altitude should move up when the up button is pressed
d. Declination should move toward the pole when the telescope is looking on the West side of the
5. Telescope Encoder Directions: The telescope encoder numbers should change in the same direction as the motors encoder numbers, ie increase while the motor is increasing.
In the Southern hemisphere, I think (b) should be "R/A should go counterclockwise when viewed from the
It's altogether confusing because for the drive, Alt=
... Henk. Telescopes: GSO 12" Astrograph, "Comet Hunter" MN152, ES ED127CF, ES ED80, WO Redcat51, Z12, AT6RC, Celestron Skymaster 20x80, Mounts and tripod: Losmandy G11S with OnStep, AVX, Tiltall, Cameras: ASI2600MC, ASI2600MM, ASI120 mini, Fuji X-a1, Canon XSi, T6, ELPH 100HS, DIY: OnStep controller, Pi4b/power rig, Afocal adapter, Foldable Dob base, Az/Alt Dob setting circles, Accessories: ZWO 36 mm filter wheel, TV Paracorr 2, Baader MPCC Mk III, ES FF, SSAG, QHY OAG-M, EAF electronic focuser, Plossls, Barlows, Telrad, Laser collimators (Seben LK1, Z12, Howie Glatter), Cheshire, 2 Orion RACIs 8x50, Software: KStars-Ekos, DSS, PHD2, Nebulosity, Photo Gallery, Gimp, CHDK, Computers:Pi4b, 2x running KStars/Ekos, Toshiba Satellite 17", Website:Henk's astro images
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
All done testing and it's outside, passed everything, phd Connects, stellarium works, sgpro works And it tracks satilites.just have to get it polar aligned and do the cable harness. I had to remove the eq6 from the field as there isn't enough room for all 3 mounts
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
I can check with lucas or dan gray ,this is his custom profile he has sent me . The mount can and is designed to do a full 360 rotation on theSkyHiker wrote: ↑Wed Dec 18, 2019 1:15 am It will hit the legs sooner with the scope upside down. Isn't there a better configuration? This is weird.
I just wonder, since this looks like a small one person shop in the Northern hemisphere, if a mistake was made in the configuration. I'm looking at the servoConfig manual, it says:
4. Motor Directions
a. Azimuth should go clockwise when pressing the right button on the handpad (birds eye view).
b. R/A should go clockwise when viewed from Polaris
c. Altitude should move up when the up button is pressed
d. Declination should move toward the pole when the telescope is looking on the West side of the Meridian.
5. Telescope Encoder Directions: The telescope encoder numbers should change in the same direction as the motors encoder numbers, ie increase while the motor is increasing.
In the Southern hemisphere, I think (b) should be "R/A should go counterclockwise when viewed from the SCP". About (a) I'm not so sure - for reasons of symmetry I think Az should move in the opposite direction in response to commands to the Northern hemisphere, while it does make sense to have Az go clockwise when you push the right button. How this jives with the telescope and motor encoders, I have no idea.
It's altogether confusing because for the drive, Alt=DEC and Az=RA. I would consult with SiTech because they must have customers in the Southern hemisphere.
I believe that profile has been made this way, more than likely it can be change, thanks for the response on it, i should double check if i can change this setting.
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- yobbo89
- Moderator
- Articles: 0
- Posts: 2599
- Joined: Sat May 11, 2019 7:44 pm
- 4
- Location: australia qld brisbane
- Status:
Offline
-
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
yes,The
scopes :gso/bintel f4 12"truss tube, bresser messier ar127s /skywatcher 10'' dob,meade 12'' f10 lx200 sct
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
cameras : asi 1600mm-c/asi1600mm-c,asi120mc,prostar lp guidecam, nikkon d60, sony a7,asi 290 mm
mounts : eq6 pro/eq8/mesu 200 v2
filters : 2'' astronomik lp/badder lrgb h-a,sII,oIII,h-b,Baader Solar Continuum, chroma 3nm ha,sii,oiii,nii,rgb,lowglow,uv/ir,Thousand Oaks Solar Filter,1.25'' #47 violet,pro planet 742 ir,pro planet 807 ir,pro planet 642 bp ir.
extras : skywatcher f4 aplanatic cc, Baader MPCC MKIII Coma Corrector,Orion Field Flattener,zwo 1.25''adc.starlight maxi 2" 9x filter wheel,tele vue 2x barlow .
- JayTee
- Universal Ambassador
- Articles: 2
- Posts: 5646
- Joined: Thu Apr 25, 2019 3:23 am
- 5
- Location: Idaho, USA
- Status:
Offline
-
TSS Awards Badges
TSS Photo of the Day
Re: new mount ,using sitech, horizon limit and star alighnment
I've been watching you all throughout the build, fantastic work.
I haven't brought this up before but I'm really nervous your tripod Pier is missing a leg....
Just wondering,
JT
I haven't brought this up before but I'm really nervous your tripod Pier is missing a leg....
Just wondering,
JT
∞ Primary Scopes: #1: Celestron CPC1100 #2: 8" f/7.5 Dob #3: CR150HD f/8 6" frac
∞ AP Scopes: #1: TPO 6" f/9 RC #2: ES 102 f/7 APO #3: ES 80mm f/6 APO
∞ G&G Scopes: #1: Meade 102mm f/7.8 #2: Bresser 102mm f/4.5
∞ Guide Scopes: 70 & 80mm fracs -- The El Cheapo Bros.
∞ Mounts: iOptron CEM70AG, SW EQ6R, Celestron AVX, SLT & GT (Alt-Az), Meade DS2000
∞ Cameras: #1: ZWO ASI294MC Pro #2: 662MC #3: 120MC, Canon T3i, Orion SSAG, WYZE Cam3
∞ Binos: 10X50,11X70,15X70, 25X100 ∞ AP Gear: ZWO EAF and mini EFW and the Optolong L-eXteme filter
∞ EPs: ES 2": 21mm 100° & 30mm 82° Pentax XW: 7, 10, 14, & 20mm 70°
Searching the skies since 1966. "I never met a scope I didn't want to keep."
∞ AP Scopes: #1: TPO 6" f/9 RC #2: ES 102 f/7 APO #3: ES 80mm f/6 APO
∞ G&G Scopes: #1: Meade 102mm f/7.8 #2: Bresser 102mm f/4.5
∞ Guide Scopes: 70 & 80mm fracs -- The El Cheapo Bros.
∞ Mounts: iOptron CEM70AG, SW EQ6R, Celestron AVX, SLT & GT (Alt-Az), Meade DS2000
∞ Cameras: #1: ZWO ASI294MC Pro #2: 662MC #3: 120MC, Canon T3i, Orion SSAG, WYZE Cam3
∞ Binos: 10X50,11X70,15X70, 25X100 ∞ AP Gear: ZWO EAF and mini EFW and the Optolong L-eXteme filter
∞ EPs: ES 2": 21mm 100° & 30mm 82° Pentax XW: 7, 10, 14, & 20mm 70°
Searching the skies since 1966. "I never met a scope I didn't want to keep."
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute