Bay for 8 foot round ExploraDome building

Discuss your home observatory!
Post Reply
User avatar
John Fitzgerald United States of America
Jupiter Ambassador
Articles: 0
Offline
Posts: 211
Joined: Mon Nov 11, 2019 12:04 am
4
Location: Arkansas
Status:
Offline

TSS Awards Badges

Bay for 8 foot round ExploraDome building

#1

Post by John Fitzgerald »


I just finished building and installing a custom 38 inch wide bay for my little round building. Pictures provided if anyone is interested.
Double and multiple star observer. Over 3,500 unique pairs logged.

No good deed goes unpunished.
User avatar
KathyNS Canada
Co-Administrator
Co-Administrator
Articles: 0
Offline
Posts: 2577
Joined: Thu Apr 25, 2019 11:47 am
4
Location: Nova Scotia
Status:
Offline

TSS Awards Badges

TSS Photo of the Day

Re: Bay for 8 foot round ExploraDome building

#2

Post by KathyNS »


John Fitzgerald wrote: Mon Oct 11, 2021 7:27 pm ... if anyone is interested.
Heck yes! Pix or it didn't happen! ;)
Image
DSO AP: Orion 200mm f/4 Newtonian Astrograph; ATIK 383L+; EFW2 filter wheel; Astrodon Ha,Oiii,LRGB filters; KWIQ/QHY5 guide scope; Planetary AP: Celestron C-11; ZWO ASI120MC; Portable: Celestron C-8 on HEQ5 pro; C-90 on wedge; 20x80 binos; Etc: Canon 350D; Various EPs, etc. Obs: 8' Exploradome; iOptron CEM60 (pier); Helena Observatory (H2O) Astrobin
User avatar
messier 111 Canada
Universal Ambassador
Articles: 0
Offline
Posts: 9400
Joined: Mon Nov 09, 2020 2:49 am
3
Location: Canada's capital region .
Status:
Offline

TSS Awards Badges

Re: Bay for 8 foot round ExploraDome building

#3

Post by messier 111 »


John Fitzgerald wrote: Mon Oct 11, 2021 7:27 pm I just finished building and installing a custom 38 inch wide bay for my little round building. Pictures provided if anyone is interested.
pics pls .
I LOVE REFRACTORS , :Astronomer1: :sprefac:

REFRACTOR , TS-Optics Doublet SD-APO 125 mm f/7.8 . Lunt 80mm MT Ha Doublet Refractor .

EYEPIECES, Delos , Delite and 26mm Nagler t5 , 2 zoom Svbony 7-21 , Orion Premium Linear BinoViewer .

FILTER , Nebustar 2 tele vue . Apm solar wedge . contrast booster 2 inches .

Mounts , berno mack 3 with telepod , cg-4 motorized , eq6 pro belt drive .

“Your assumptions are your windows on the world. Scrub them off every once in a while, or the light won't come in.”
― Isaac Asimov

Jean-Yves :flags-canada:
User avatar
John Fitzgerald United States of America
Jupiter Ambassador
Articles: 0
Offline
Posts: 211
Joined: Mon Nov 11, 2019 12:04 am
4
Location: Arkansas
Status:
Offline

TSS Awards Badges

Re: Bay for 8 foot round ExploraDome building

#4

Post by John Fitzgerald »


Here are a few pictures of the process:



Total outlay for this was just under $180. Some of the the materials were already lying around taking up space. If I had to buy it all from scratch, it would have cost maybe $250. That's far better than the $525 plus shipping of nearly $200 for a factory bay. This one is (inside) 38 inches wide, (slightly wider than a factory bay), 48 inches tall at the dome, tapering to 42 inches tall at the outside. It's about 18 inches deep at the center, and 24 inches at the sides.


I did not have to cut a hole. I removed one sheet of metal sliding, which covered about 33 inches wide and full height, and trimmed about 5 inches off the width of an adjacent sheet, using some relatively cheap electric shears from Harbor Freight, which I had purchased for a previous, larger project. Those shears are worth their weight in a semi precious metal. I also used them to trim down the new sheets to fit.

The roof of the bay is 1/2 inch PT ply with 1/4 inch HDPE sheet on top. The curved rings started out as 2x2x1/8 inch aluminum angle. I cut the bottom one down to 1.25 on the face leg. The floor is 3/4 inch PT ply.

I put 2x4 studs inside, where the bay joins the original round building, for additional attachment points. Shows in the inside picture.

First use was last evening. It's amazing the difference it makes for moving around that small dome, with the accessories in the bay.

It was a lot of work. If I counted labor, it might cost more than the commercial version, but in retrospect, building it proves to me I can do it. I didn’t have to wait months for delivery, and it's a custom fit for my relatively old dome.
Attachments
fully framed, painted with flat "coal colored paint" #3
fully framed, painted with flat "coal colored paint" #3
Framing nearly complete, glued with "Gorilla Glue" poly glue #2
Framing nearly complete, glued with "Gorilla Glue" poly glue #2
Preliminary fitting #1
Preliminary fitting #1
inside view #10
inside view #10
Finished. Held up with adjustable deck support #8
Finished. Held up with adjustable deck support #8
Finished. Side view #9
Finished. Side view #9
Sides going on #6
Sides going on #6
in process, still temporarily supported #7
in process, still temporarily supported #7
in process #5
in process #5
sizing up to building.  Temporarily supported. #4
sizing up to building. Temporarily supported. #4
Last edited by John Fitzgerald on Tue Oct 12, 2021 1:24 pm, edited 5 times in total.
Double and multiple star observer. Over 3,500 unique pairs logged.

No good deed goes unpunished.
User avatar
John Fitzgerald United States of America
Jupiter Ambassador
Articles: 0
Offline
Posts: 211
Joined: Mon Nov 11, 2019 12:04 am
4
Location: Arkansas
Status:
Offline

TSS Awards Badges

Re: Bay for 8 foot round ExploraDome building

#5

Post by John Fitzgerald »


My pictures are somehow out of chronological order, but you get the gist of it. I have them numbered in order of construction.
Double and multiple star observer. Over 3,500 unique pairs logged.

No good deed goes unpunished.
Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

Return to “Home observatories”